36v EZGO Will Not Move And Solenoid Is Not Clicking [Causes and Solutions] 

Who would like to face such issues like 36V EZGO will not move and solenoid is not clicking? Definitely, nobody would. 

So, why does this problem occur and how to prevent it? Well, the most possible reason for this problem is a faulty solenoid. Bad battery connections and corroded terminals are also some other reasons. 

Fortunately, you can simply avoid these circumstances by following some easy tips. But what are they? Let’s figure them out.

What Happens When 36v EZGO Will Not Move And Solenoid Is Not Clicking?

When your 36V EZGO doesn’t move and the solenoid is not clicking, you will encounter certain issues coming with your club car. Here are the most common symptoms to this problem: 

• Poor battery performance
• Less clicking sound from the solenoid 
• No clicking sound when the cart turns on
• Contacts are overheated
• No electricity to the controller 
• The starter fails to disengage 

What Causes 36v  36v EZGO golf cart will not move and solenoid is not clicking? 

Over time, your 36V EZGO golf cart can develop various symptoms as discussed earlier. Usually, these problems occur from different origins. 

Here are some possible causes for an EZGO 36V club car not moving and clicking issue: 

• Poor battery connection
• Corroded or clogged battery terminals
• Faulty solenoid
• Dirty or damage solenoid contacts
• Loosen or worn out wiring connections
• Problems with the motor or controller
• Defective ignition switch 

What to do if the solenoid is not clicking and 36v 36v EZGO golf cart will not move?

A bad solenoid on your 36V EZGO can be repaired just like other components. By doing so, you can also save some extra expenses. There are few methods you can try to fix the solenoid that’s not clicking. Let’s discuss those solutions: 

Check and replace the battery 

The most common reason for an EZGO 36V not moving is the defective battery on the car. On an electric golf cart, the battery is the main source of power that allows it to start the cart and run. 

Over time, the battery tends to get damaged and fails to send power to the solenoid. The problem can also occur because of low battery voltage. 

So, start by checking the battery voltage across the battery terminals using a multimeter. If the voltage is lower than it requires, recharge or replace the battery. 

However, if you need to replace the battery, then you should expect to pay anywhere between $800 and $15,00. Here, the labor cost ranges between $75 and $140. 

Diagnose the wiring

Wirings or connections are another important part of any type of electrical cart. They connect the solenoid with the battery, controllers and contacts. If the wings are corroded, eroded, or disconnected, the system will not function and your EZGO will not move or click. 

So, if there’s no issue with the battery, then check the wirings to the solenoid and make sure that they are secure and clean. If you find any issue, replace the wires even if it seems trivial. 

On average, it will cost up to $800 to replace a bad wiring on a cart. But if you just need to reconnect a wiring or clean corrosion, it won’t cost more than $150. 

Once you’ve replaced the wires, rev up the engine and see if you hear the clicking sound from the solenoid. If YES, then the problem is fixed. Otherwise try our next solution. 

Inspect the solenoid contacts

Dirty solenoid contacts are another major reason for the 36V EZGO not starting or the solenoid doesn’t click. When the contacts are dirty, it leads to poor electrical connection. 

So, inspect the contacts if they are dirty or wear out. If you find them dirty, simply clean them using a wire brush or a contact cleaner. Then, check the solenoid to see if it’s clicking again. If not, you may need to replace the solenoid. 

The replacement cost of a solenoid on a 36V EZGO golf cart is expected between $50 and $175 for the part and installation. 

Check the solenoid

If the contacts inside the solenoid are all right, then the problem might be with the solenoid itself. When the solenoid becomes faulty, it fails to convey the energy from the battery to the motor to move the vehicle. 

So, when the solenoid on your 36V EZGO club cart is not clicking and the cart isn’t moving, test the solenoid for continuity. Use a multimeter and touch the probes to the solenoid terminals to see the continuity. If there’s no continuity, it is necessary to replace the solenoid.   

You can also check the solenoid by bypassing it with a jumper wire. Bypass the solenoid to watch out if the vehicle moves. If it does, then it means you should replace the solenoid. 

Test the microswitches

Sometimes , there are a few microswitches inserted on the accelerator and the forward and reverse switch on the EZGO 36V golf cart. With time, these switches can be broken or disconnected and cause problems with the solenoid. 

So, if the solenoid is still malfunctioning and the cart is not running, test that microswitches and ensure they’re functioning properly. But if they’re not, then adjust or replace the switches as needed. 

Generally, a microswitch on an EZGO golf cart costs between $11.99 and $15.99. If you call a mechanic to help you with that, then it may cost around $60 as the labor cost. 

Inspect the motor

If the problem is not with the battery, solenoid, or switches, then it could be an issue with the motor or controller. Faulty motor or controller can prevent an EZGO from moving. 

In this case, it could be better to consult a professional mechanic to diagnose and repair the problem. 

Contact a professional

When your personal inspections fail to fix your 36V EZGO, it’s better to contact a professional technician. They’re definitely more knowledgeable than you and can help you to fix your golf cart more effectively. 

Tips to Maintain the Solenoid on a 36v EZGO golf cart

It is crucial to maintain the solenoid on a 36V EZGO golf cart for proper functioning and extended lifespan. Here are few tips you can follow to maintain the solenoid effectively: 

• Over time, the solenoid can  accumulate dust and debris on its surface. So, clean the solenoid regularly to remove dust, debris or corrosion. 
• Inspect the wirings and connection points to ensure that all are secure and properly connected. 
• You should also check the voltage level on your EZGO golf cart battery. 
• It’s also a good idea to test the solenoid periodically to see if it’s working properly. 
• Use a small amount of lubricant or dielectric grease to the moving parts of the solenoid to reduce friction. 
• It’s also better to use a solenoid cover to protect it from moisture. 
• Finally, follow the manufacturer’s guidelines that may provide additional maintenance steps. 

Read More:

• How to Do Ez go Golf Cart Charger Troubleshooting? [With Easy Solutions]
• EZ Go Golf Cart Electric Motor Troubleshooting & Fix Guide
• EZ Go Golf Cart Controller Troubleshooting Guide! Things You Need To Do!
• E-Z-Go Electric Golf Cart Not Moving: Troubleshooting Guide
• Club Car Golf Cart Battery Light Stays On | What to Do?

FAQs

You may still have some confusion and queries in your mind regarding the 36 Volt EZGO solenoid that doesn’t click and move. So, here we’ve listed some frequently asked questions to answer the probable queries: 

Conclusion

Most of the golf cart owners face the same problem like the solenoid is not clicking and the cart refuses to run. It’s very normal as the solenoid can easily go bad. 

In this case, testing the solenoid will help you to diagnose the starting issue with your cart. When you get the solenoid bad, don’t be late to contact an ASE certified technician to replace it.