How to Replace a Golf Cart Drive Belt (Gas Carts): Steps, Sizes and Wear Checks

A gas golf cart drive belt wrapped around the drive and driven clutches.

Quick answer: To replace a gas golf cart drive belt, take out the key and let the engine cool. Press the belt into the driven (rear) clutch and turn the clutch to walk the belt off. Then lift it off the drive clutch. Fit the new belt on the drive clutch first, roll it onto the driven clutch, and test drive slowly.

Below is how to replace a golf cart drive belt on most gas carts, step by step. It also covers how to tell when a belt is worn out, which size fits common Club Car and Yamaha models, and what to check if the new belt still slips.

How Do You Replace a Golf Cart Drive Belt?

Here is the short version. The detailed steps come later in this guide.

  1. Park on level ground, take out the key and chock the wheels.
  2. Let the engine and clutches cool.
  3. Open the engine area by lifting the seat or a body panel.
  4. Walk the old belt off the driven (rear) clutch.
  5. Lift the belt off the drive (engine) clutch.
  6. Fit the new belt in reverse order: drive clutch first, then driven clutch.
  7. Test drive at low speed.

Do You Have to Remove the Clutch to Change the Belt?

No. On most gas carts, you can swap the belt with both clutches still in place. You only need to remove a clutch if you are servicing or replacing the clutch itself. If your job needs that, see our clutch removal guides: [INTERNAL LINK: clutch removal articles].

This guide is for gas carts only. Electric carts do not have a CVT drive belt.

How Do You Know Your Drive Belt Needs Replacing?

Replace the belt if you see damage on it, if the cart slips or gets noisy, or if the belt measures longer than its wear limit.

Visual Signs of a Worn Belt

  • Cracks, pitting or dry rot: A belt with any of these should be replaced as soon as possible.
  • Fraying: Loose cords or ragged edges on the sides.
  • Glazing: A glossy, hardened layer on the faces that touch the clutch sheaves.

Glazing alone does not always mean you need a new belt. If the belt is still within its wear limit, you can lightly sand the glazed faces with fine-grit sandpaper. This can improve grip and reduce slipping.

Watch for these signs while you drive:

How to Measure Belt Stretch

A belt gets longer as it wears. You can check this with a flexible tape measure. Here is how it works on a Yamaha G29/Drive gas cart:

  1. Remove the belt.
  2. Wrap the tape around the outside of the belt to measure its circumference.
  3. Compare the result to the spec of 41-1/8 in.
  4. If the belt measures 1/8 in or more over spec (41-1/4 in or longer), replace it.

For other models, compare against the length printed on the belt or listed in your owner’s manual. For a deeper look at slipping problems, see [INTERNAL LINK: Yamaha belt slipping article].

Diagram of a drive belt loop with spec 41-1/8 in, keep under 41-1/4 in, replace at 41-1/4 in or longer.Yamaha G29/Drive Belt CheckMeasure outside circumferenceSpec: 41-1/8 inUnder 41-1/4 in: keep41-1/4 in or longer: replace
Yamaha G29/Drive belt stretch check: replace at 1/8 in over spec.

Which Drive Belt Fits Your Golf Cart?

Pick the belt that matches your cart’s brand, model, year and engine. Then check it against the number printed on your old belt. Here are two verified examples:

CartYearsBelt sizeOEM part numbers
Club Car gas, Kawasaki engine1992-20151 in wide x 37 in longCheck your old belt or manual
Yamaha G29/Drive gas2007-20111-1/16 in x 41-1/8 in ODJW1-G6241-00, JW1-G6241-10-00

How Do I Know What Size Belt My Cart Needs?

  1. Note your brand, model, year and engine type.
  2. Find the serial number plate to confirm the model year.
  3. Read the part number printed on the old belt.
  4. Measure the old belt’s width and length.
  5. Buy only if all of these match the new belt’s listing.

Keep in mind that a worn belt will measure a little long. Trust the printed part number over your measurement.

E-Z-GO drive belts vary by year and engine. Check your owner’s manual or ask a dealer before you buy.

What Tools and Safety Steps Do You Need Before You Start?

You only need basic tools:

  • Socket set (for panels or covers, if your model has them)
  • Work gloves
  • Flexible tape measure
  • Wheel chocks
  • Flashlight

Follow these safety steps:

  • Turn the key off and remove it.
  • Park on level ground and chock the wheels.
  • Let the engine and clutches cool fully.
  • Keep your fingers out from between the clutch sheaves. They can close on your hand when the clutch turns.

Some models have their own steps, such as covers to remove or torque values for bolts. Follow your model’s owner’s manual for these.

Step-by-Step: Removing the Old Drive Belt

  1. Get to the belt. Lift the seat or remove the body panel, depending on your model. Use the flashlight to find both clutches. The drive clutch is on the engine. The driven clutch is toward the rear axle.
  2. Spread the driven clutch. Push the belt down into the driven clutch, or pull it up, so the sheaves spread apart. This creates slack.
  3. Walk the belt off. While you hold that pressure, turn the driven clutch by hand or roll the cart slowly. The belt will climb up and off the sheave.
  4. Remove it from the drive clutch. With the belt loose, slip it off the drive clutch.
  5. Inspect the clutch faces. Look for damage, debris, oil or glazing on the sheaves. Wipe them clean before you go on. Oil or grime on the faces will make a new belt slip.

Step-by-Step: Installing the New Drive Belt

  1. Check the direction. Look for an arrow printed on the new belt. Point it in the direction of rotation. If there is no arrow, match the way the old belt sat.
  2. Fit the drive clutch first. Loop the belt around the drive (engine) clutch.
  3. Roll it onto the driven clutch. Start the belt on the top of the driven clutch. Push it into the sheaves and turn the clutch until the belt rolls into place.
  4. Check the fit. Make sure the belt sits evenly in both clutches and is not twisted.
  5. Close up and test. Refit any panels, remove the chocks and drive slowly first. A new belt needs a short break-in period, so go easy on it at first.

Which Way Does a Golf Cart Drive Belt Go On?

Follow the arrow on the belt if it has one. If it doesn’t, put the new belt on the same way the old one came off. Take a photo before you remove the old belt so you can match it.

Can You Tighten a Drive Belt Instead of Replacing It?

Usually not. A gas cart drive belt does not have a simple tension adjuster. The clutches control how tightly the belt grips. If the belt has stretched past its wear limit, replace it.

How Often Should You Check a Golf Cart Drive Belt?

Check it at least once a year. The E-Z-GO TXT gas owner’s manual says to check the drive belt for cracks, fraying and excessive wear every year or every 250-300 hours.

There is no fixed replacement date. Replace the belt when it shows wear, fails the tape-measure check, or starts to slip. A good habit is a quick look during routine service and before hilly or heavy use.

What If the New Belt Still Slips or Squeals?

Some noise during break-in can happen. If slipping or squealing keeps going, check these common causes:

  • Wrong belt size: Compare the part number and size with your cart’s spec.
  • Glazed or oily clutch faces: A dirty sheave makes even a new belt slip.
  • Worn clutch parts: Worn sheaves, springs or other parts can stop the belt from gripping.

Use this decision rule: if the correct new belt still slips, look at the clutches next, not the belt. For brand-specific help, see [INTERNAL LINK: clutch upgrade and removal articles].

Golf Cart Drive Belt FAQs

Can you fix a glazed golf cart drive belt?

Sometimes. If the belt is glazed but still within its wear limit, you can lightly sand the glossy faces with fine-grit sandpaper. This can improve grip and reduce slipping. If the belt is cracked, frayed, pitted or stretched past its wear limit, replace it instead of sanding it.

Do electric golf carts have a drive belt?

No. Electric golf carts do not have a CVT drive belt. The belt and clutch setup is found on gas carts. On a gas cart, one belt runs between the drive clutch on the engine and the driven clutch near the rear axle, so only gas carts need belt replacement.

What size drive belt does a Yamaha G29 gas cart use?

A 2007-2011 Yamaha G29/Drive gas cart uses a 1-1/16 in x 41-1/8 in OD drive belt. The OEM part numbers are JW1-G6241-00 and JW1-G6241-10-00. Replace the belt if it measures 41-1/4 in or longer around the outside, which is 1/8 in over spec.

What size drive belt does a Club Car gas cart use?

Club Car gas carts with a Kawasaki engine, built from 1992 to 2015, use a drive belt that is 1 in wide and 37 in long. Before you buy, confirm the size by reading the part number printed on your old belt or by checking your owner’s manual.

Which clutch does a new golf cart drive belt go on first?

Put the new belt on the drive clutch first. That is the clutch on the engine. Then start the belt on top of the driven clutch near the rear axle. Push it into the sheaves and turn the clutch until the belt rolls into place. Check that it is not twisted.

Kawsar Avatar