How to Regrip Golf Clubs at Home: 10 Steps, Tools and Drying Time

Close-up of new rubber grips on a set of golf clubs.

Quick answer: Here is how to regrip golf clubs. Slice off the old grip with a hook blade and strip all the old tape. Wrap the shaft in new double-sided grip tape. Coat the tape and the inside of the new grip with solvent. Slide the grip on in one push, line it up, and let it dry at least four hours.

How do you regrip golf clubs? (Quick answer)

Yes, you can regrip your own golf clubs. The job takes basic hand tools, some solvent and a little patience. Golf Pride’s installation guide breaks it into 10 steps:

  1. Remove the old grip.
  2. Remove the old tape.
  3. Secure the club.
  4. Measure and cut new tape.
  5. Apply the tape.
  6. Pour solvent into the grip.
  7. Pour solvent over the tape.
  8. Slide the grip on.
  9. Wipe it and seat it.
  10. Check alignment.

This method suits beginners who own basic hand tools. Set aside a free evening for a full set, and leave time for the grips to dry before your next round.

What tools do you need to regrip golf clubs?

To regrip golf clubs at home, you need a hook blade, double-sided grip tape, grip solvent, a bucket or tray, towels, new grips, and a way to hold the club steady. This list follows Golf Pride’s regripping tool list.

ItemWhy you need itRequired or optional
Hook bladeCuts the old grip without the edge touching the shaftRequired
Double-sided grip tapeHolds the new grip in place once the solvent driesRequired
Grip solventLubricates the tape so the grip slides on, then evaporatesRequired
Bucket or trayCatches solvent that drips or spillsRequired
Towels (one damp, one dry)Cleans the shaft, covers the cap end, wipes off solventRequired
Vise with rubber shaft clampHolds the club steady while you tape and installOptional (you can brace the club with your feet)
Heat gun or hair dryerSoftens stubborn old tape so it peels off more easilyOptional
New gripsOne per club, in the size you wantRequired

A hook blade beats a straight utility knife. The hook shape points the cutting edge up and away from the shaft, so you slice the rubber instead of the club. A straight blade can slip and scratch or nick the shaft.

Do you need a vise to regrip clubs?

No. A vise makes the job easier, but Golf Pride says you can brace the club with your feet instead. If you do use a vise, put a rubber shaft clamp between the jaws and the shaft. Bare metal jaws can crush or scratch a shaft.

What can you use instead of grip solvent?

Use a solvent made for regripping. Lamkin’s regripping instructions list mineral spirits grip solvent as a required item. A store-bought grip solvent also works. Don’t swap in random household liquids. The solvent has to lubricate the tape and then evaporate fully, or the grip can stay loose.

Lamkin also suggests catching extra solvent in a tray so you can reuse it on the next club. Work in a ventilated area away from open flames.

Step-by-step: how to regrip a golf club

These steps follow Golf Pride’s installation guide. Do one club at a time, start to finish.

Step 1–2: Remove the old grip and tape

  1. Remove the old grip. Slide the hook blade under the mouth of the grip, and slice along its full length. Always cut away from your body. Peel the grip off the shaft.
  2. Remove the old tape. Strip off all of the old tape. If it sticks, warm it with a heat gun or hair dryer to soften it. Once no tape is left, wipe the shaft with a damp towel until it is completely clean.

Step 3–5: Secure the club and tape the shaft

  1. Secure the club. Clamp the shaft in a vise with a rubber shaft clamp, or brace the club with your feet. The clubhead should point straight up or down so you can check alignment later.
  2. Measure and cut the tape. Cut a strip of double-sided grip tape about 1 inch longer than the grip.
  3. Apply the tape. Peel off the backing and run the tape lengthwise down the shaft, leaving about 1 inch hanging past the butt end. Wrap it smoothly around the shaft. Twist the extra inch and tuck it into the end of the shaft.

Step 6–8: Add solvent and slide the grip on

  1. Put solvent in the grip. Hold the grip over a bucket. Cover the vent hole in the cap with your finger. Pour solvent into the grip, cover the mouth, and shake it to coat the inside.
  2. Put solvent on the tape. Pour the solvent from the grip over the taped shaft, so the tape is fully covered.
  3. Slide the grip on. Place a towel over the cap end, because solvent can spray out. Push the grip onto the shaft in one smooth motion. Do not stop halfway.

Step 9–10: Seat and align the grip

  1. Wipe it and seat it. Wipe off all the solvent. Then tap the cap end firmly on the ground to push the grip fully onto the shaft.
  2. Check alignment. Line up the grip’s logo or tick marks with the clubhead. Twist the grip to fix it before the solvent dries.

How do you line up a new grip straight?

Line up a new grip using its tick marks and logo. Most grips have small marks at the mouth and the cap. Check that those marks and the logo sit straight in line with the leading edge of the clubhead.

Prefer the logo facing down? Turn the grip 180 degrees before you slide it on. Then align it the same way, using the tick marks.

Work fast. Once the solvent evaporates, the grip locks in place. Line it up right after you seat it, while it still turns.

How long should regripped clubs dry before you play?

New grips need to dry for at least four hours before you play. That is Golf Pride’s recommendation.

An easy way to stay safe is to regrip the night before a round. The clubs then have all night to dry.

Warning: If you swing too soon, the grip can twist on the shaft. Then it may dry crooked or feel loose.

How do you make grips bigger with extra tape?

Add wraps of tape under the grip to make it thicker. Most players use one layer of double-sided tape. Each extra wrap adds a small amount of size, according to Golf Pride’s build-up guide:

Extra wraps of tapeAdded grip size
1About 1/64 inch
2About 1/32 inch
4About 1/16 inch (roughly the jump from standard to midsize)

Two rules matter here. The top layer must always be double-sided grip tape, so the grip bonds. Also, stagger the build-up layers so you can’t feel a seam under your hands.

Not sure what size you need? See our [INTERNAL LINK: golf grip size guide] before you add tape.

How do you regrip clubs with graphite shafts safely?

Graphite is easier to damage than steel. A nick or deep scratch can weaken the shaft. Follow these rules:

  • Use only a hook blade. Keep the cut shallow. Never drag a straight blade along graphite.
  • Clamp with rubber. Always use a rubber shaft clamp. Never use bare metal vise jaws.
  • Peel, don’t scrape. Remove old tape gently. Warm it with a hair dryer if it sticks, instead of scraping hard.

How often should you regrip golf clubs?

A common guideline is to regrip about every 30 to 40 rounds, or every 12 to 18 months for casual golfers, per Golf Today. If you play or practice often, regrip sooner.

Watch for these signs that it’s time:

  • The grip feels slick or looks shiny.
  • The color is faded or uneven.
  • You see cracks in the rubber.
  • There are worn spots where your thumbs sit.

Heat can wear grips down. If you often leave clubs in a hot car or garage, check your grips more often.

Should you regrip clubs yourself or pay a shop?

Regrip yourself if you want to do a full set, have basic tools and don’t mind a learning curve. Pay a shop if your setup carries more risk or you’re short on time.

DIY suits you if…A shop suits you if…
You want to regrip a full setYou have graphite shafts and no rubber shaft clamp
You own or will buy basic toolsYou want oversize or specialty putter grips installed
You’re fine with a learning curveYou need the clubs done the same day
You want control over tape build-upYou’d rather avoid any risk to the shaft

The trade-off: With DIY, you buy the tools once and then reuse them for every future regrip. You also control exactly how much tape goes under each grip. A shop brings experience and lowers the risk of damaging a shaft. Shop labor prices vary, so ask your local shop for a quote.

Common regripping mistakes to avoid

  • Leaving old tape on the shaft. Fix: Strip it all off, then wipe the shaft clean with a damp towel.
  • Using too little solvent. Fix: Coat the inside of the grip and the full length of the tape.
  • Stopping halfway while sliding the grip on. Fix: Push it on in one smooth motion.
  • Letting the grip dry crooked. Fix: Check the tick marks and logo right after you seat the grip.
  • Playing before four hours are up. Fix: Regrip the night before a round.
  • Cutting toward your body. Fix: Always pull the hook blade away from you.

Frequently Asked Questions About Regripping Golf Clubs

Can I regrip my own golf clubs?

Yes, you can regrip your own golf clubs at home. You need a hook blade, double-sided grip tape, grip solvent, a tray or bucket, towels and new grips. A vise helps but is optional. Set aside an evening for a full set, and let the grips dry at least four hours before you play.

Why use a hook blade instead of a utility knife to remove grips?

A hook blade is safer for the shaft. Its curved shape points the cutting edge up and away from the shaft, so you slice the rubber instead of the club. A straight utility knife can slip and scratch or nick the shaft. This matters most on graphite shafts. Always cut away from your body.

How do you remove stubborn old grip tape from a shaft?

Warm stubborn tape with a heat gun or hair dryer, then peel it off. Heat softens the adhesive so it lets go more easily. On graphite shafts, peel gently instead of scraping hard. Once all the tape is gone, wipe the shaft with a damp towel until it is completely clean.

How long should the grip tape be when regripping?

Cut the double-sided tape about 1 inch longer than the grip. Run it lengthwise down the shaft so about 1 inch hangs past the butt end. Wrap it smoothly around the shaft, then twist the extra inch and tuck it into the end of the shaft before you add solvent.

Can you reuse grip solvent?

Yes, you can catch and reuse extra solvent. Lamkin suggests holding the grip and shaft over a tray so the runoff collects there, then using it on the next club. Use a solvent made for regripping, such as mineral spirits grip solvent. Work in a ventilated area away from open flames.

Kawsar Avatar