Changing Shaft on Adjustable Driver – A to Z Explanation

The shaft of your golf driver has an essential influence on your capability to hit the golf ball and to ensure the utmost swing speed, distance, and accuracy. However, it’s typical for your shaft to start breaking after a specific time, or its efficiency has decreased significantly. 

What should you do in that case? Should you purchase a brand-new driver or just replace the shaft? With open eyes, changing the shaft on an adjustable driver will be a cost-effective solution. 

But, there are some factors that you should consider and finalize whether it’s wise to replace the shaft. If everything matches your situation, then the replacement process comes in. So many things to manage, right? 

Don’t worry; we have everything you need to know to make a wise decision, along with an easy-to-follow guide for the replacement process. 

Changing Shaft on Adjustable Driver

When Should You Change the Adjustable Driver Shaft?

In the past couple of decades, there has been a considerable increase in the costs of drivers. Consequently, changing any part of your driver could end up being an expensive undertaking. 

In this light, you shouldn’t throw the old shaft out just because you don’t like it anymore.

Rather you should change the shaft only when your driver demands it. Consider the following scenarios in which you should change the old shaft.

Unusual Swing Speed Variations

Have you noticed a sudden descent or increase in the rate of swing on your driver? If this is the case, then it may well be worthwhile to have a new shaft. 

However, it is usually worth this if you do it later only if there is any consistency in change and it has happened multiple times. 

Broken Drive Shaft

Broken Drive Shaft
Broken Drive Shaft

If your driver shaft has only minor dents or cracks, take advantage of replacing the shaft only at a minimal cost instead.

According to many experts, it’s safe to change the shaft when the damage is only up to six inches on any one side. 

So, it’s needless to say that severe damages will urge a replacement of your driver. As a bonus tip, inspect your driver shaft to find any minor damage and change it before something worse happens. 

Golf Ball Ballooning

You need to change the shaft on your adjustable driver if you notice the ball consistently flinging upward.

If you observe the golf ball repeatedly ballooning, it will fall from the air with a great deal of backspin and without rolling much distance. 

Most often, ballooning is caused by the spinning of your golf club’s shaft and prevents you from achieving a sufficient carry distance.

How to Change Shaft on Adjustable Driver

Shaft on Adjustable Driver

Replacing the shaft of an adjustable driver is distinct from that of a standard driver. The following steps can be a guide to replacing the driver shaft.

Nevertheless, the specific procedure can fluctuate from driver to driver depending on their specifics and which tools will be required.

Before attempting replacement, make sure all your gear is appropriate for the job and that you have the correct tools. If all seems okay, then you can proceed to the following steps.

Remove Your Old Shaft

To begin with, you first have to remove the existing shaft. The process is somewhat different depending on whether the existing shaft is broken or just detached from the link. 

However, the same replacement process will apply regardless of the condition of the shaft. Here, a utility knife should be used to remove the ferrule from the hosel in order to remove the club from the shaft. 

Utilize a clamp to hold the club shaft as a shield to prevent damage to the shaft. The driver shaft and club head remain attached with epoxy glue.

You have to use a heat gun to soften the glue. Now, remove the driver head to the old shaft and do not drop it. Wait until the shaft completely cools. 

Clean the Shaft and Hosel Properly

Now it’s time to clean the shaft thoroughly. For this, use a carbide-tipped knife to scrape off all polyurethane and paint from the top of your new shaft. Make sure you don’t wind up cutting the runner flat or cutting out too much. 

Put on sanding paper to remove all glue and make the surface smooth. You can use a wire brush in case an excess amount of glue is present in the hosel. 

Melting the epoxy generally would have been better if the hosel had first been thoroughly cleaned out.

Do your best not to dig down too deep, or you may damage the hosel or the bore plug. Using a rag, thoroughly clean out the insides of the hosel to remove the old epoxy. 

Prepare New Epoxy Mixture and Apply It

Epoxy Mixture

Take the fresh shaft epoxy and create a mixture on the cardboard using the craft stick.  It is recommended to adhere to the manufacturer’s directions when mixing the epoxy to ensure optimal results. 

Take a small amount of the new epoxy and put it inside the ferrule. Slide it onto the shaft using one end of the shaft as a guide. 

Now, add more of the epoxy glue and discharge it into the stage of the shovel, so it is correctly spread when you push the shaft.

For an even spread of the epoxy throughout the shaft, you can rotate the shaft somewhat in either direction.

Connect the New Shaft

Connect the New Shaft

Now detach the club from your shaft clump. After that, you have to place the grip end of the club onto the ground while the butt end is on your hand to push the shaft. Push sufficiently to ensure it goes inside all the way and at the proper depth. 

Make sure you don’t push too hard, as it can damage the attaching point, the shaft, or the ferrule. Wipe off the shaft with soft cloths and set it aside for twenty-four hours before it’s operational. 

Benefits of Changing Shaft on An Adjustable Driver 

There are two enticing benefits of replacing the old shaft of an adjustable driver. Have a look at the benefits below:

Enhanced Performance

When golf players struggle to have good swing speed with a particular golf driver, simply swapping out the old shaft can help to increase their game a great deal. 

Particularly for novice golfers who have a hard time maintaining consistent swing speed, changing the golf driver’s shaft can help realize a considerable improvement in their game.  

If the swing speed power begins dropping degrees or rises steeply, changing the golf driver shaft may aid the return to the starting swing speed level.

Cost Effective Solution

Replacing the shaft with a brand-new driver, which is rated no more than 5 years old, can substantially boost efficiency while reducing costs.

Because the labor and resource materials costs have skyrocketed, the price of new drivers has gone up considerably. 

If you decide to replace only the shaft of your driver and you don’t really care about the brand, the cost will be significantly less.

Things to Consider While Swapping Shaft

Does replacing the old shaft of your adjustable driver make sense? Or should you purchase a new model? It’s entirely up to you to make these sorts of decisions. 

However, there are some factors that you should consider when you’ve decided to change the shaft. Check them below:

Be Cautious About the Fitment

An important point that you must remember when replacing a golf driver shaft is to make sure that it’s the right fit for the club head.

If the shaft you choose doesn’t fit into the club head correctly, you’ll most likely end up with poor performance and damage to the driver. 

Assess the Features

If you’re hoping to opt for a driver that absorbs vibrations or has an exceptionally high thrust, be sure that you carefully consider the shaft that you select.

You can accomplish this by testing your shaft with a driver having similar features as your own driver at a local golf club fitter shop ahead of time. 

Be Careful about the Brand 

Changing the shaft is a major benefit as it allows you to modify your golf driver to better suit your needs.

It also allows you to choose from lightweight and flexible shafts that work with your style. But the complexity comes forward when you go for shafts from premium brands.

Oftentimes, it can render higher overall costs, even sometimes higher than purchasing a moderate golf driver.  So, think about your budget and choose the brand cautiously

Keep an Eye on the Glue and Drying Time

Although much of the physical work performed to replace a shaft on your golf driver can be done quickly, it generally takes approximately 24 hours. This is because you have to wait until the epoxy glue is completely dried. 

That means what type of glue you’re going to use can be an influential factor when replacing the driver shaft.

FAQs

Is there any query other than itching in your thoughts? Don’t worry; we have collected some important information in our short FAQ section. Hope this will give you answers to your queries. 

Is Changing Shafts On Adjustable Drivers Worth It? 

Replacing your old shaft with a new one will be worth your investment if you’re satisfied with the club, but you just need to boost its performance. Replacing a slightly damaged or old shaft is absolutely less expensive than purchasing a new club.

How Much Does It Cost To Change Shaft On Adjustable Drivers?

The overall cost of changing shafts on adjustable drivers can vary depending on what type of shaft you’re going to use, the driver you have, your preferred performance, and so on. However, the average cost can be around $250 to $550.

How Long Does It Take To Change A Shaft On Adjustable Drivers?

The main process can take a maximum of 40 minutes. However, the main part is drying the epoxy glue properly, and this can take even a day. 

Conclusion

At this point, you might have gained substantial knowledge about changing shafts on adjustable drivers. Before we sign out, we recommend you focus on our end words. 

So, frankly speaking, changing the shaft of a driver which is already near its end won’t give you any dramatic changes. Besides, if you have an advanced driver but your shaft is backdated, this won’t be beneficial either. 

So, whenever you notice a drop in swing speed or the overall performance of your club, assess the driver properly and then decide what you should do. Our guide is always here for you.

Read More:

How To Choose The Right X Stiff Iron Shafts? [Perfect Fit]

Changing Shaft On Adjustable Driver – A To Z Explanation

Mitsubishi Tensei AV Blue Vs Hzrdus Smoke Shaft Comparison

True Temper Elevate 95 Vs 105: Which Golf Shaft to Choose?

Similar Posts